• The BIOGAS 300 provides single sample point monitoring for CH4
• Ideal for small-scale anaerobic digestion sites
• Modbus or 4-20mA data output
• Simple to operate – push button operation
• 0-100% CH4 measurement
• Easy to read backlit display through transparent enclosure door
• Last reading stored for on-screen viewing
• IP65 rated ABS enclosure

Benefits of the BIOGAS 300

1. No training required
2. Zero service downtime
3. Field proven equipment
4. Simple user calibration
5. Field proven technology
6. Quick and easy self-installation
7. Low cost of ownership
8. Compact self-contained system

The post Biogas 300 appeared first on CSL.

About

• CH4 CO2 and O2 – standard measurements
• H2S, H2 and CO – choice of up to two optional measurements
• Modular design enabling hot-swap for serviceability and onsite maintenance
• User calibration function to maintain accuracy & ensure data reliability in extreme temperatures
• ATEX and IECEx certified for use in potentially explosive gas atmospheres – zone 2
• ISO / IEC 17025 calibration for optimal accuracy
• Ability to monitor the gas control process before and after desulphurisation
• Continuous monitoring option
• Up to 4 sample points to monitor the complete gas control process
• IP65 rated for weather proofing
• Built in liquid level monitoring with a dedicated alarm to inform the user that the contents of the catchpot requires emptying or an optional automated moisture removal drain
• Gas alarms and fault notifications
• 6 x 4-20mA outputs
• Modbus RTU communication
• Optional Profibus and Profinet communication
• Clear, visual and informative colour display
• Optional heater to extend operating temperature range to -20°C
• Extended Warranty & Service pack options

Benefits

• Customisable to site requirements
• Zero operational downtime for servicing
• Product reliability and longevity
• Protect expensive capital equipment from damaging gases
• Maximise operational efficiency through optimising the AD process
• Operational within hazardous areas
• Ease of operation, integration and installation
• Minimal through-life costs
• Local support for peace of mind

The post Biogas 3000 appeared first on CSL.

• The G100 enables quick verification and validation of CO2 levels in incubators
• Used and distributed globally to the medical and research industries
• CO2 measurement levels between 0-20%
• Improved accuracy on CO2 readings
• Optional extra gases: measures O2 (0-100%); dual temperature probe (0-50 degrees C); humidity sensor (0-100%)
• Large data storage and data download available for all your readings

Benefits

1. Accurate readings and quick verification of CO2 incubator levels – a reading takes under a minute
2. Using one instrument makes analysis simple and easy
3. Built in gas moisture removal protects the G100 from water ingress
4. Dual temperature probes help you to adjust the temperature to stablise conditions within your incubator and helps you analyse temperature variation
5. The G100’s easy to read menu and large, well lit display makes data readings quick and simple
6. User friendly software specifically created for the G100 helps you make sense of your data storage and download

Used by

• Embryologists
• Lab technicians
• Scientists
• Stem cell researchers

The post G100 appeared first on CSL.

• Measures CO2 0-100%
• Quick verification of CO2 levels
• Built in gas moisture removal
• Improved accuracy on CO2 readings

Benefits

1. Measure O2 0-100%
2. Dual temperature probes
3. Humidity sensor 0-100%
4. Data download and storage
5. Accurate CO2 readings
6. Quick verification of CO2 levels
7. Time saving with dual temperature probes
8. Large data storage and user friendly software for download
9. Easy to read large well lit display
10. Built in gas moisture removal

The post G110 appeared first on CSL.

• Measure CO2 0-10000ppm
• Built in gas moisture removal
• Quick verification of CO2 levels for site audits
• Improved accuracy on CO2 readings

Benefits

1. Measure O2 0-100%
2. Dual temperature probes 0-50 degrees C
3. Humidity sensor 0-100%
4. Data download and storage
5. Stowseek probe for illegal immigrant detection

The post G150 appeared first on CSL.

Crowcon Gasmasters large display shows gas levels from all detectors simultaneously and enables system adjustment and testing using buttons on the front panel. Crowcon Gasmaster can operate ‘stand-alone’ or interface with any alarm devices and control systems using a selection of outputs. Alarm messages can be customised to indicate the name or location of any detector in alarm

User-friendly

• Menu system is intuitive and easy to use
• All functions, from day-to-day operation to re-calibration, can be carried out from the front panel.
• Event log feature – enables system fault and alarm history to be viewed

Versatile input and output features

• Provides analogue, relay and Modbus outputs.
• Flexibility – Gasmaster can monitor up to four detectors.
• Two levels of independent alarm per channel – can be configured to suit site requirements
• Remote inhibit and re-set facilities – enables control from any point on your site

The post Gasmaster appeared first on CSL.

• All day-to-day functions are available from the front panel – push buttons for simple operation
• Unique bar-graph display per channel – provides instant representation of gas concentrations
• Common alarm LEDs on the display card – the whole rack status can be checked at a glance.

Flexible architecture

• System is limitlessly expandable
• Modular construction – ultimate customisation and minimal wiring
• Industry-standard analogue outputs – will integrate fully with existing rack-mounted protection systems on-site
• Optional relay modules – flexible and cuts down on configuration and monitoring cabling

Easy maintenance

• Each channel is inhibited separately – plant safety is not compromised during checks
• Routine calibration from front panel – reduces service overheads by half
• One universal gas card – reduces spares holding

The post Gasmonitor appeared first on CSL.

The GES Gas-Tec portable Flame Ionisation Detector (FID) sensor can measure minute levels of hydrocarbons, allowing detection of levels from 1 to 10,000ppm of methane in less than 2 seconds. Even gas leaks from distribution pipes located under main roads or highways can be quickly detected. Extremely portable, the Gas-Tec is shoulder carried allowing the independent probe to be positioned easily around valves and flanges.

Supplied with a refillable hydrogen cylinder (60 hours use), rechargeable lithium-Ion batteries (22 hours use), angled probe assembly, multi region mains charger, carry strap, quick start guide, user guide, filters and military grade carry case.

Features

GPS: Enhances record keeping by assigning latitude, longitude and sea level to data readings.
Users are also able to view the current location, offering the precise location to back-up crews for
immediate leak management.

Data and event logging: Gas-Tec allows users the ability to download full survey information via
the ‘drag and drop’ USB interface for survey traceability.

Intuitive functionality: LCD and soft keys offering full sequence instruction, in-operation options,
service and calibration set-up and alerts.

Tried and tested: Based around the original Gas-Tec ‘engine’ detection method. The next generation is
therefore already proven, fit for purpose and suited to the trials of every day use.

Enhanced electronic controls: Offering extended battery and cylinder life. Pressure and flow transducers
manage H2 and sample flow rates.

The post GES Gas-Tec FID Mk5 appeared first on CSL.

Extremely portable, the Gas-Tec is shoulder carried allowing the independent probe to be positioned easily around valves and flanges.

Supplied with a refillable hydrogen cylinder (60 hours use), rechargeable lead acid batteries (15 hours use), angled probe, battery charger, DIN socket for battery charging and data output to chart recorder, filters and carrying case.

Features

• Very easy to activate and use – minimal training required
• Hydrogen fuel source for improved accuracy
• Rechargeable batteries – 15 hour usage per charge
• 60 hour operational life of H2 cylinder

Leak Identification

• Identification of concentration – from 1 ppm to 10,000 ppm (Can be extended upto 100,000 ppm)
• Geiger counter style click, with Crescendo alarm for increased concentrations
• Very quick 2 second response time
• Loudspeaker or earphone options, for background noise isolation
• Fast to read analogue display
• Twin ranges with optional range extension
• For use for all hydrocarbon detection

The post GES Gas-Tec Mk4 FID (New & Reconditioned) appeared first on CSL.

• 1 to 12 channels (including 3 for fire) – up to 12 devices can be monitored by reviewing just one control panel, saving time and manpower
• Each channel has 1 fault level and 3 alarm levels which can be combined in any pattern to trigger up to 32 output relays
• Push buttons on front display – day-to-day operations are easily undertaken
• LED display panel lights – faults are easily seen and whole system can be checked at a glance

Installation and maintenance

• Modbus compatability – no extensive cabling required; cable connections within the unit are easy
• Space within units for access to cable terminals
• Separate zones can be individually inhibited – you can work on specific areas without affecting the rest of the system
• Modular construction – replacement parts if required, which plug straight in

Compliance and reliability

• Validated to IEC 61508 (SIL 1) – demonstrates system dependability
• System monitors relays continuously
• Internal battery pack* – power outs are not a problem.

The post Vortex appeared first on CSL.